Multi-Beam Antennas: Increased Wireless Capacity with Enhanced Spectral Efficiency

Parent Category: 2019 HFE

By John Howard and Steve Jalil

Multi-beam antennas provide increased wireless capacity with enhanced spectral efficiency. Typically, wireless providers use three sectors in a 360° coverage area. With multibeam antenna systems, spectrum and capacity are multiplied. In this paper, a 5GHz, 6-dual polarized beam system is presented. The system covers 90 degrees in the azimuth and was deployed at the Sky Tower in Auckland, New Zealand. Live data was gathered at street level and presented.

Introduction

ET Industries has been in production of 5G Antenna Systems since 2006. The antenna systems of the 2006 production covering the CBRS band are shown in figures 1 and 2. The system has a total of 48 beams in 360 degrees. Frequency was repeated three times per 90 degrees thus providing 12 times higher spectral capacity from a single cell.

1903 5G fg01

Fig. 1 • 2006, 3.5GHz, 5G phased array

1903 5G fg02

Fig. 2 • 2006, 3.5GHz, 5G beamforming network.

ETI has designed as many as 32 dual polarized beams within 120° coverage, providing 96 sectors in 360°. The benefits of such a system are higher data throughput, higher customer capacity, increased spectral efficiency, and reduced number of cell sites versus traditional antennas. With the use of multiplexers, several frequency channels can be merged and transmitted into a single beam producing a multi-channel sector. For every channel that is transmitted into the beam, an increase in capacity and throughput factor is obtained.

In this paper, a 6-dual polarized beam system is presented. The system covers 90 degrees in the azimuth and was deployed at the Sky Tower in Auckland, New Zealand.

Deployment

The architecture of the ETI 5G Antenna System deployed at the Sky Tower in Auckland, NZ is detailed in figure 3. The system deployment consisted of six MIMO access points interfaced with two beamforming networks, one per polarization. The 5 GHz phased array had a 128-element geometry per polarization. The 5G antenna system provided a radiation pattern of six dual polarized beams in a 90-degree azimuth footprint.

1903 5G fg03

Fig. 3 • 5GHz system diagram deployed at Sky Tower.

Results

Measurements were taken at street level in the city of Auckland up to 10 km from the transmission point. Speeds of 200Mbps per 20MHz channel per beam were witnessed. Modulations of 256QAM were produced in the field. This resulted in 1.2Gbps aggregate from one antenna across the 90-degree azimuth coverage. The Smart MIMO Switching capabilities of the system were also witnessed. The links automatically changed from MIMO-A (Diversity) to MIMO-B (Multiple Streams) based on link conditions to increase efficiency, link stability, as well as increased data capacity.

1903 5G fg04

Fig.4 • Point of Transmission from Skytower.

During the deployment, ETI repeated the same frequency on beams 3 and 8, essentially doubling this channel’s speed. Simultaneous readings at the same channel were taken demonstrating no interference and a substantial increase of capacity by repeating the channel. See figure 6 for frequency reuse of beams 3 and 8 carrying the same channel.

1903 5G fg05

Fig. 5 • View from behind the 21 dB gain antenna system. 6 beams, M3 (left outermost beam), M2, M1, M8, M7 and M6 (right outermost beam).

The actual measurements are too numerous to present herein, but representative measurements are shown in Tables 1 and 2. Table 1 consists of the readings in beam mode 3 and table 2 of beam mode 1. RF 1 and RF 2 are the two paths for the dual polarization in downlink and uplink. During the trial different measurements at different distances were gathered as follows: received signal strength (RSSI), Signal-to-noise and distortion ratio (SINADR), data rates in Mb/s and MIMO for both uplink and downlink.

1903 5G tb01

Table 1 • Beam mode 3 street level results.

1903 5G tb02

Table 2 • Beam mode 1 street level results.

1903 5G fg06

Fig. 6 • Repeated channels beams M3 and M8.

Some areas where there is MIMO-A is because of non-optimized street level positions of the subscriber module. This in turn decreased the link efficiency. Proper planning and optimization of the subscriber modules’ position will allow for MIMO-B links everywhere.

Conclusion

Traditional 360° cells sites are divided into three sectors. With the multi-beam antenna system, spectrum and capacity can be multiplied. The benefit of such a system is higher data throughput, higher customer capacity and increased spectral efficiency. The beam crossing can be designed to cross between 3 to 10 dB with side lobe levels of 25dB. As the number of beams increases, so does the capacity and throughput. With the use of multiplexers, multi-channel sectors can be created to further enhance the benefits of the system. The multi-beam antenna system is clearly the solution to the ever-growing demand of data usage and network capacity for the finite amount of spectrum.

1903 5G fg07

Fig.7 • Street level reading, in the distance the Sky Tower where the ETI multibeam antenna is transmitting.

About the Authors

John Howard and Steve Jalil are with Electromagnetics Technologies Industries, Boonton, New Jersey.

References

[1]J. Howard. J. Logothetis and J. Wilson, “Beamformer: Broadband RF Technology for Integrated Networks”, Antennas and Propagation Society International Symposium, 1996. AP-S. Digest, vol.3, pp.1632,1635, July 21-26 1996.

[2]J. Howard and J. Desai, “Multibeam Antenna Serves Broadband Wireless Coms”, Microwaves & RF, Vol. 47 Issue 6, pp. 61, June 2008.

[3]Patent No.9407005. “Isolation of Polarizations in Multi-polarized Scanning Phased Array Antennas.” Issued 2016.